原子吸收光谱法测定拉伸断口铬镍钼钛钢样品中主成分

研究了毫克级铬镍钼风样品中主成分镍的火焰原子吸收光谱法（FAAS法）和铬、钼、钒、钛、铝的塞曼恒温平台石墨炉原子吸收光谱法（ZSTPF－AAS法）。采用了微波溶样技术作为防污染样品预处理技术，采用石墨管硅涂层改进技术提高了仪器的测试精度。其中铬、镍、钼、钒、钛、铝的相对标准偏差分别为2.7%,0.97%,8.6%,7.3%,1.7%,7.3%。其加标回收率分别为96.5%,97%,96.7%,93%,98%,91%。通过分析，发现在较低温度下铬镍钼钛钢断面上有轻微的钼偏析现象，可能是拉伸断裂的主要化学影响因素。     

石墨炉原子吸收法测定生物样品中镉的几种基体改进剂的比较

本文比较了磷酸二氢铵、氟化铵、硫酸铵、氯化钯、氯铂酸以及氯铂酸与多种有机酸的混合试剂在测定ＧＢＷ猪肝标准物质中镉时基体改进效果，其中，氯铂酸的基体改进能力最强，猪肝标准物质的回收率在９０％     

硅的原子吸收光谱分析进展

对近十年来用原子吸收光谱法测定硅的情况进行评述．重点介绍用石墨炉测定硅时，为了避免硅与石墨炉中碳形成难熔碳化硅影响测定硅的灵敏度而使用的各种化学改进剂，涂层石墨管和一些新的实验技术．引用参考文献４２篇．     

DETERMINATION OF DEGREE OF CRYSTALLINITY OF NYLON 1212 BY WIDE-ANGLE X-RAY DIFFRACTION

Based on the X-ray scattering intensity theory and using the approximate expression for the atomic scattering factor, the correction factors for three crystalline peaks and an amorphous peak of Nylon 1212 were calculated and the formula of degree of crystallinity of Nylon 1212 was derived by a graphic multipeak resolution method. The degree of crystallinity calculated from the WAXD method is compatible with those obtained by density and calorimetry methods.     

粉末化学镀法制备的NiB／TiO2非晶态合金催化剂对环丁烯砜加氢反应的催化性能

 采用诱导沉积法及粉末化学镀法分别制备了纯态NiB及负载型NiB／TiO2非晶态合金催化剂．用XRD，ICP，SEM，TEM和DSC等手段对催化剂的物性及TiO2载体与NiB非晶态合金之间的相互作用进行了表征，考察了非晶态合金的结构、组成、形貌和热稳定性，并将其用于环丁烯砜加氢反应中．结果表明，相对于NiB而言，NiB／TiO2催化剂具有优良的热稳定性和催化活性，这缘于NiB和TiO2载体之间的相互作用及载体的分散作用．     

非晶态Fe－W合金镀层的表面改性

将Ｆｅ－Ｗ非晶态镀层在铬酸盐钝化液中进行化学钝化与电化学钝化，使之形成含铬钝化膜。阳极极化曲线说明，钝化后镀层的孔蚀电位向正向移动了约１．６８Ｖ；Ｆｅ－Ｗ非晶镀层在氯化钠溶液中浸泡近１ｈ表面发生严重腐蚀，而经钝化处理的镀层浸泡１个月，表面无变化，仍具有金属光泽。     

石墨炉原子吸收法测定土壤中镉的测量不确定度评定

石墨炉原子吸收法测定土壤中镉的不确定度主要来源于称量样品、定容样品消解液、测定样品消解液中镉的质量浓度及测定土壤水分引入的不确定度。对各不确定度分量进行了计算,求得合成标准不确定度和扩展不确定度分别为0.0026、0.005mg/kg。镉测量不确定度的主要来源是测定样品消解液中镉质量浓度引入的不确定度。     

Melt-crystallization, glass transition and morphology of a (R)-3-hydroxybutyrate pentamer

The melt-crystallization of an oligo[(R)-3-hydroxybutyrate] with five repeating units has been analyzed using standard and temperature-modulated calorimetry, optical microscopy, and atomic force microscopy. Specimens of different crystallinity and supermolecular structure were generated by variation of the rate of cooling of a quiescent melt, or by variation of the temperature of isothermal crystallization. Completely amorphous samples can be obtained by cooling of the melt at a rate of 40 K min⁻¹, or faster, to a temperature lower than the glass transition. The crystallinity depends on the crystallization temperature. The maximum enthalpy-based crystallinity of about 40-45% is obtained by crystallization at temperatures lower than the temperature of the maximum crystallization rate, which is between 310 and 320 K. Analysis of the apparent heat capacity in metastable structural equilibrium reveals reversible melting at temperatures between 320 and 370 K by observation of an excess heat capacity above the level of the vibrational heat capacity, i.e., in the temperature range of irreversible reorganization and melting. The reversible melting is discussed in the context of coupling of the crystalline and amorphous phases, and compared to earlier studies on oligoethylene and oligo(oxyethylene). The presence of crystals causes formation of a rigid amorphous fraction of about 30% at a crystallinity of 40%. Optical and atomic force microscopy reveal spherulitic crystallization. At relatively high crystallization temperature, and in the early stage of the crystallization process, dendrites are observed which finally yield spherulites of decreased perfection. Larger spherulites of higher perfection grow at relatively low crystallization temperature, as deduced from the appearance of the Maltese cross, and the regularity of banding. The band spacing is less than 5 μm, as is accurately determined by atomic force microscopy. The temperature dependence of the spherulitic growth rate is in accord with the calorimetric analysis of the crystallization rate.     

Study of temperature transitions in solid poly(oxymethylene) by thermal analysis methods

Poly(oxymethylene)s with different molecular mass and chemical structure were studied using DSC, dynamic mechanical relaxation, thermomechanical analysis, and thermogravimetry.Molecular mobilities of two types were found in the amorphous phase of poly(oxymethylene). Unconstrained chains of poly(oxymethylene) soften at –70°C and then amorphous chains with different restraints from the crystalline phase are successively activated in a wide temperature interval.Dedicated to Professor Bernhard Wunderlich on the occasion of his 65th birthdayThis work has been supported by DuPont Company     

蒙脱石-石墨-聚氯乙烯复合电极测定制药废水中苯酚

报道了当制药废水PH8．0时，用蒙脱石－石墨－聚氯乙烯复合电极可以直接测定苯酚的含量而不受水杨酸存在的干扰，苯酚浓度在1．0μg/mL-25.0μg/mL范围内峰电流与浓度有良好的线性关系，I＝1．262c-0.046，相关系数r=0.998，检出限为0．1μg/mL，用该方法测定模拟制药废水中苯酚，其平均回收率为101．7％。